Skip to navigation – Site map

HomeNuméros33Studies of Objects: manufacturin...Technological study of gold jewel...

Studies of Objects: manufacturing skills and alloy selection

Technological study of gold jewellery pieces dating from the Middle Kingdom to the New Kingdom in Egypt

Étude technologique de pièces d’orfèvrerie datées du Moyen Empire au Nouvel Empire en Égypte
Lore G. Troalen, Maria Filomena Guerra, Jim Tate and Bill Manley
p. 111-119

Abstracts

This paper presents a technological study of items of Egyptian jewellery from the collections of the National Museums Scotland: a pendant from the 19th century BC; objects from the 16th century BC royal burial unearthed at Qurneh; two gold finger-rings dated to the 14th century BC; and a group of pendants from the 13th century BC. The objects were examined using optical microscopy, X-radiography and Scanning Electron Microscopy (SEM). In addition, the elementary compositions of alloys and solder joints were investigated using air-path X-ray fluorescence (XRF), proton-induced X-ray analysis (micro-PIXE), and energy-dispersive X-ray analysis (SEM-EDS). This preliminary study provides information about the evolution of alloy composition and the use of alluvial gold, and illustrates the Ancient Egyptian goldsmiths’ skills in working with wires, granulation and joining techniques.

Top of page

Full text

1. Introduction

1Numerous works on jewellery originating from Ancient Egypt are conveniently cited in studies by Lucas (1929, re-edited 1962), Ogden (1982; 2000) and Andrews (1990). However, relatively little work is available combining elemental analysis with technological study; the principal exceptions are Lucas (1962) and Schorsch (1995) on jewellery from the burial of Wah, and Lilyquist (2003) on jewellery from the burial of the foreign wives of Thutmose III, while others are cited by Schorsch (2001). As a result, little is known about the alloys used in Ancient Egypt, or about manufacturing techniques such as filigree and granulation. In order to shed more light on this technology, we applied a multi-disciplinary approach to the analysis of several artefacts in the collections of National Museums Scotland (NMS).

2NMS holds about 6,000 objects from Ancient Egypt and Sudan, including gold and electrum jewellery that has hitherto not been the subject of significant scientific study. The collections cover all periods from the Predynastic to the Roman Empire, and a good proportion of the artefacts derive from repuTable archaeological excavations carried out during the 19th and 20th centuries. An example of this is the intact royal burial from Qurneh, near Thebes, acquired by the former Royal Scottish Museum (a precursor of NMS) in 1909, and dated to the 16th century BC. The Qurneh burial included the ornately decorated coffin and mummy of a young adult woman and the simpler coffin and mummy of a child (Petrie, 1909), both of whom had been buried with a range of grave goods, including jewellery of gold, electrum, ivory and faience (Eremin et al., 2000; Manley et al., 2002). In addition to the gold necklace described elsewhere in this volume (Tate et al., 2010), the woman was provided with: four gold bracelets made from a D-section bar bent into a ring and soldered (A.1909.527.16 + A-C); an electrum girdle consisting of twenty-six scaraboid beads and twelve barrel beads threaded on a double string (A.1909.527.17); and two gold earrings consisting of four penannular hoops soldered together (A.1909.527.18 + A). The child’s mummy wore a simpler gold necklace (A.1909.527.11), and two loops, each consisting of three-and-a-half gold rings, which are usually described as earrings (A.1909.527.43 +A).

  • 1 The pendant is 41 mm long by 19 mm high. It was excavated in the burial of a ten years old girl in (...)
  • 2 See Martin (1974, nos. 275 and 280). Dimensions: A.1883.49.2, diameter of hoop 28 mm (internal 16 m (...)
  • 3 The fly-pendants might have formed part of an official’s usekh-collar, cf. an example in The Egypti (...)

3To the purpose of carrying out an initial investigation into the varieties of alloys and production techniques used in Ancient Egypt, we studied the Qurneh jewellery along with a small collection of other gold items spanning the period between the 19th and the 13th centuries BC, containing: a fish-shaped pendant (A.1914.1081) from a tomb at el-Harāgeh from the mid-19th century BC1; two gold finger-rings with decorated bezels (A.1883.49.2 + A.1883.49.8) from the Amarna royal tomb of the late 18th Dynasty (14th century BC);2 and sixteen fly-shaped pendants (A.1977.140 A-P), assumed, on stylistic grounds, to date from the 19th Dynasty (13th century BC)3.

2. Methods

4The objects were examined at NMS using a stereo-microscope (Olympus SZX12 x 7-90) equipped with a digital camera (Olympus DP70) and CamScan Scanning Electron Microscopy in Secondary Electron mode (SEI), and their construction investigated using a 300kV Pantak X-radiography system.

5The elemental composition of the alloys was determined using an Oxford Instruments ED 2000 air-path X-ray fluorescence (XRF), with a Rhodium target X-ray tube collimated to a point of about 2 x 1.5 mm, coupled to a Si(Li) detector using the Oxford Xpert Ease software. In addition, proton-induced 3MeV X-ray analysis (micro-PIXE) was carried out at the external beamline of the AGLAE accelerator at the Centre de Recherche et de Restauration des Musées de France (Guerra and Calligaro, 2003; Dran et al., 2004; Guerra, 2008). Energy Dispersive X-ray analysis (SEM-EDS), using the Noran Vantage system and Vista software, was used to characterise inclusions of platinum-group elements (PGE) and investigate other compositional information. All SEM-EDS measurements were performed at the analytical working distance of 35.0 mm at 300 s measurement with a voltage of 20 kV or 25 kV.

Figure 1: Qurneh girdle (A.1909.527.17): (a) OM image showing some deformation of barrel beads; (b) X-radiograph showing small barrel beads that have slipped inside a wallet bead.
Figure 1 : Ceinture de Qurneh (A.1909.527.17) : (a) image sous loupe binoculaire illustrant la déformation des perles coniques ; (b) radiographie X illustrant les petites perles coniques à l’intérieur d’une perle en portefeuille.

Figure 1: Qurneh girdle (A.1909.527.17): (a) OM image showing some deformation of barrel beads; (b) X-radiograph showing small barrel beads that have slipped inside a wallet bead.Figure 1 : Ceinture de Qurneh (A.1909.527.17) : (a) image sous loupe binoculaire illustrant la déformation des perles coniques ; (b) radiographie X illustrant les petites perles coniques à l’intérieur d’une perle en portefeuille.

6Table 1 presents the compositional analysis of ternary alloys of gold-silver-copper standards, showing the inter-instrument compatibility. The compositions of the objects can be found in Table 2, and are summarised in the ternary diagram in Fig. 3. For the Qurneh jewellery, all compositional results are from PIXE analysis, except for the girdle, which, like most of the jewellery, was analysed with XRF.

Table 1: Compositional results (in wt%) of gold-silver-copper alloy standards by PIXE, XRF and SEM-EDS.
Tableau 1 : Compositions (en %) des alliages étalons en or-argent-cuivre par PIXE, FX et MEB-EDS.

Table 1: Compositional results (in wt%) of gold-silver-copper alloy standards by PIXE, XRF and SEM-EDS.Tableau 1 : Compositions (en %) des alliages étalons en or-argent-cuivre par PIXE, FX et MEB-EDS.

3. Results

7All the jewellery showed indications of wear, particularly the Qurneh girdle and one of the Amarna finger-rings (A.1883.49.2). For the girdle, we were able to observe loose decoration, and deformations of the edges of the beads and of holes in the wallet spacers where they sit against the beads (Fig. 1a). Occasionally, some small barrel beads are trapped within wallet beads (Fig. 1b). For the finger-ring, we observed that the granules on the bezel are flattened, except those immediately beside the bezel hole, which remain perfectly spherical (see Fig. 5).

Gold Alloys

8We observed and analysed PGE inclusions, ranging from a few to a few hundred microns in diameter, in all the jewellery items except the fly-pendants. PGE inclusions are characteristic for gold from alluvial deposits (Ogden, 1976), and can be found in all the Qurneh objects. However, only a single inclusion was found in the woman’s earrings, and a single small inclusion was found in the tail of the fish-pendant (Fig. 2a). By comparison, the Amarna finger-rings contain numerous inclusions, which may indicate the use of gold from other deposits. The inclusions show a range of composition, with an average of 36% iridium, 42% osmium and 22% ruthenium, corresponding well with compositions reported by Meeks and Tite (1980) in their investigation of Egyptian objects from the British Museum, and also with the range otherwise expected for Egyptian deposits (Ahmed, 2007). We also observed variable ratios of iridium, osmium and ruthenium in the PGE inclusions within the same object, making the formulation of any conclusions regarding the gold deposits difficult. However, the absence of platinum, rhodium or palladium indicates that the gold is not associated with the alluvial deposits of Yubdo (Wallaga) in Ethiopia (Molly, 1959).

Figure 2: PGE inclusions in pendant (A.1914.1081) from el-Harāgeh by OM; (b) Qurneh child’s necklace (A.1909.527.11) by SEI.
Figure 2 : Inclusions de platinoïdes (a [Voir planche couleur]) du pendantif (A.1914.1081) d’el-Harāgeh sous loupe binoculaire ; (b) du collier d’enfant de Qurneh (A.1909.527.11) au MEB.

Figure 2: PGE inclusions in pendant (A.1914.1081) from el-Harāgeh by OM; (b) Qurneh child’s necklace (A.1909.527.11) by SEI.Figure 2 : Inclusions de platinoïdes (a [Voir planche couleur]) du pendantif (A.1914.1081) d’el-Harāgeh sous loupe binoculaire ; (b) du collier d’enfant de Qurneh (A.1909.527.11) au MEB.

9With regard to the alloys (Table 2; Fig. 3), we observed that most of the artefacts were made from gold with a silver content ranging from 2 to 20%. The exceptions from the Qurneh burial are made of electrum, as defined by Pliny, i.e. a gold alloy in which the silver content is greater than 20% (Natural History, XXXIII): in the girdle, the silver content reaches 52.5-53% in the wallet beads and the barrel beads, and in the child’s necklace, the silver content varies between 27 and 32%. The tail of the Harāgeh pendant is also made of electrum containing 51.7% silver. Therefore, variation in alloys does not seem to be linked to chronology, but rather to type and presumably use of the objects, as well as perhaps to colour (Schorsch, 2001; Frantz and Schoesch, 1990), considering that the Egyptian words for gold (noub) and silver (hat) are colour-oriented.

10Copper is generally present in quantities of less than 2%; however, some objects exhibit a copper content higher than 3%. The wallet beads of the Qurneh girdle contain 3.7% copper, while in the barrel beads the copper content varies from 2.8 to 7.4%. We found 3.3% copper in the tail of the fish-pendant, and, finally, the fly-pendants exhibit up to 9% copper. It seems unusual for Egyptian gold deposits to contain more than 2% copper (Ogden, 2000), so most of the jewellery could have been manufactured using native alloys. For the wallet and barrel beads of the girdle, and the tail of the pendant, copper in the range of a few percent could have been added to a silver-rich electrum alloy. For the fly-pendants, the alloys could have been produced by adding copper to a native alloy with a relatively high silver content of 25% (such as the one that is found, for example, in the Qurneh child’s necklace). The addition of copper to debase gold is usually reported from the 18th Dynasty onwards, with copper-contents reaching 75% in some artefacts (Lucas, 1962: 229; Ogden, 2000). However, the amount of copper found in the barrel beads of the girdle clearly indicates that this process was in use since the 17th Dynasty.

Figure 3: Ternary diagram (gold, silver, copper) showing the average alloy composition of the jewellery investigated (for some objects, multiple analyses of the different components were undertaken).
Figure 3 : Diagramme ternaire (or, argent, cuivre) montrant la composition moyenne des alliages des pièces d’orfèvrerie analysées (pour certains objets l’analyse a été effectuée pour leurs différentes parties).

Figure 3: Ternary diagram (gold, silver, copper) showing the average alloy composition of the jewellery investigated (for some objects, multiple analyses of the different components were undertaken).Figure 3 : Diagramme ternaire (or, argent, cuivre) montrant la composition moyenne des alliages des pièces d’orfèvrerie analysées (pour certains objets l’analyse a été effectuée pour leurs différentes parties).
  • 4 In some apparent instances of forgery, the gold composition is exactly 22 carat, corresponding to E (...)
  • 5 Compositions from assay analysis by W.B. Pollard (1908).
  • 6 These new analyses confirm the surface analysis undertaken by Eremin et al. (2000).

11The Qurneh adult jewellery forms a specific group in Figure 3, with a relatively high gold content ranging between 87.8% and 95.2%. The child’s earrings show a similar composition, with 82.5% and 83.7% gold, but with a higher level of copper, which may indicate an addition meant to harden the alloy. According to Ogden (2000), Egyptian gold during the 2nd millennium BC typically contained 15-30% silver and copper in amounts lower than 2%, while the use of the cementation method to refine gold was not practised there before the 1st millennium BC (Ramage and Craddock, 2000). Such expected compositions were identified in the Qurneh child’s necklace, the Harāgeh pendant, and one of the Amarna finger-rings (A.1883.49.8), as well as in published jewellery from the tomb of the foreign wives of Thutmose III (Lilyquist, 2003). Indeed, Lilyquist (2003) argues that, in the collections of the Metropolitan Museum, only forgeries have alloys with gold content above 80%4. Nevertheless, three of four items analysed from the tomb of Yuia and Tjuiu (Tomb KV46, early 14th century BC) are at least 82% gold (Lucas 1962: 545), and one contains 96.4% gold, 1.9% silver, and less than 1% copper (Lucas 1962: 545)5. At NMS, the Qurneh woman’s earrings contain 95.6% gold, 4.1% silver and 0.2% copper6, while one Amarna finger-ring (A.1883.49.2) contains 98.2% gold, 1.7% silver and 0.1% copper. Such analyses indicate that Ancient Egyptians had access to gold of exceptional purity, either from alluvial deposits, or by importing from abroad (James, 1992). With regard to the Qurneh jewellery, at least, Nubian gold must be considered a possibility, because the burial itself shows definite cultural links with Nubia (Eremin et al., 2000; Manley et al., 2002). However, without further studies of contemporary objects, we cannot establish specific provenances for the placer gold used to manufacture the jewellery.

Solder Analysis

12There are but few published analyses of solders from Egyptian jewellery, with the exception of the study of a necklace from the burial of Wah, dated to the late 11th Dynasty (Schorsch, 1995), and of some objects dated to the 18th Dynasty (Lilyquist, 2003). The common joining technique in Ancient Egypt might have been colloidal hard soldering (or diffusion bonding), using a copper salt and organic adhesive. Hard soldering using an alloy with a lower melting point than that of the alloy to be soldered (Maryon, 1949) is considered less usual (Ogden, 1992; Lilyquist, 2003). However, on beads from the Wah burial, Schorsch (1995) found an atypical joining technique, perhaps involving hard soldering by adding different amounts of copper to the basic alloy; and the investigation of a ring from the Qurneh necklace has shown the use of a hard solder alloy made by adding copper (Tate et al., 2009).

Figure 4: Detail of solder in Qurneh child’s earring (A.1909.527.43) by OM and (b) Qurneh adult’s earrings (A.1909.527.18) by SEI.
Figure 4 : Détail de la soudure des boucles d’oreilles de Qurneh de l’enfant (A.1909.527.43) sous loupe binoculaire; (b) de l’adulte (A.1909.527.18) au MEB.

Figure 4: Detail of solder in Qurneh child’s earring (A.1909.527.43) by OM and (b) Qurneh adult’s earrings (A.1909.527.18) by SEI.Figure 4 : Détail de la soudure des boucles d’oreilles de Qurneh de l’enfant (A.1909.527.43) sous loupe binoculaire; (b) de l’adulte (A.1909.527.18) au MEB.

13Distinguishing between different soldering techniques is difficult when using only non-invasive analyses. However, the Qurneh jewellery clearly exhibits the use of hard soldering in the fabrication of the adult’s gold earrings and bracelets, and of the child’s earrings, as well as the necklace. The child’s earrings seem to be melted from over-heating while hard soldering to create joins between the different rings (Fig. 4a); Petrie also noted that they “had been over-heated while on a mandril in the furnace for soldering; the solder had stuck them together, and they parted and began to drop away, being half melted” (Petrie, 1909). PIXE analyses of the soldered area show an increase in the copper content to 7%, with a silver content of 12%. In the soldered area of the adult’s bracelets, the copper level reached 6%, with 10% silver (Table 2).

Table 2: Compositional results (in wt%) for all the objects analysed by PIXE, XRF and SEM-EDS.
Tableau 2 : Compositions (en %) des alliages des objets analysés par PIXE, FX et MEB-EDS.
Voir lien en annexe
See PDF below

14The XRF investigation of the terminal part of the Qurneh necklace gave an estimate of 80% gold, 15% silver and 5% copper. The PIXE investigation of the solder between the tubes of the adult’s earrings indicated about 2% more copper than for the main body (Table 2). All these compositions correspond to a natural alloy with a fusion temperature slightly lower than the composition of the objects (Scott 1990), as is the case with the hard soldering of the beads of the necklace (Tate et al., 2009).

Granulation

15Granulation is obtained by joining spheres to a metal sheet using hard soldering techniques or copper salt (Lilyquist, 1993). One of the first examples of granulated objects in Egypt is a gold cylinder-pendant, also from el-Harāgeh, which shows the use of hard soldering (Ogden, 1992). A similar morphology in the joining areas is found for the granules of an Amarna finger-ring (A.1883.49.2), details of which can be seen in Figure 5. EDS surface analysis of the granules showed that they are heterogeneous in composition (top: 2.8% copper, 7.9% silver, 89.4% gold; bottom: 2.7% copper, 3.3% silver, 94.0% gold).

Figure 5: Detail of granulation observed on the bezel of the finger-ring A.1883.49.2 by SEI.
Figure 5 : Détail de la granulation du chaton de la bague A.1883.49.2 au MEB.

Figure 5: Detail of granulation observed on the bezel of the finger-ring A.1883.49.2 by SEI.Figure 5 : Détail de la granulation du chaton de la bague A.1883.49.2 au MEB.

16Although these compositions are unlikely to correspond to the sulk composition – due to surface enrichments this could indicate a decoration undertaken in two stages. Experimentally, it is difficult to obtain an accurate quantitative analysis on such three-dimensional objects, which is probably the reason for the high variability of copper and silver analyses in the soldered areas. However, the indication is that in the top row, the copper content ranges from 5 to 13%, and silver from 7 to 12%, while in the bottom row the copper content ranges from 4 to 7%, and silver from 6 to 11%, which could indicate the use of separate hard solders in each row, with different melting points.

Construction and wirework

17The Amarna finger-rings show a similar mounting technique, whereby a wire is coiled around the hoop and enters the bezel (Fig. 6a). This may be analogous to technology from late 5th millennium Egypt, when rings could be made with “small strings of beads, gold-foil bands and wires of copper or silver closed by twisting the ends together” (Andrews, 1990).

18In the case of finger-ring A.1883.49.8, the round section of the hoop is reduced, and has been worked into a wire that crosses the bezel and is coiled upon each extremity. In the case of finger-ring A.1883.49.2, a much thicker hoop has been worked at the terminals into a thinner section and passed through the bezel, while, in addition, a wire is coiled round the hoop, crossing the bezel. Similar techniques may be seen in finger-rings in the British Museum (Andrews, 1991: 164-165, 175) and necklaces from the burial of the foreign wives of Thutmose III (Lilyquist, 2003: 196).

19Hammering, block-twisting, strip-drawing and strip-twisting have all been suggested as possible techniques for producing wires in antiquity (Oddy, 1977). Although no specific work published on Ancient Egyptian wires exists, hammering was usual in Bronze Age jewellery according to Petrie, strip-drawing was identified by Williams (1924), although this has been significantly questioned, while strip-twisting was largely discussed by Carroll (1972). As regards Ancient Egyptian objects, Williams (1924) suggests the use of strip-drawing and strip-twisting, while Scheel (1989) suggests that thick wires were produced by strip-twisting and thinner wires by block-twisting. Hammered wire presents facetted surfaces; block-twisted wire has a more or less round section with a solid interior; while both strip-drawing and strip-twisting result in a round section wire with a hollow interior (Oddy, 1977).

20For the Amarna finger-rings, we identified the following characteristics: the wire of A.1883.49.2 is relatively thick, with a section that is solid but sometimes not circular, whereas the wire of A.1883.49.8 is solid, rounder in section, and shows some longitudinal lines. In the wires of both rings, we observed flaking and overlapping of gold, possibly corresponding to rolling and burnishing treatments (Fig. 6b). Excluding the effects of wear, we observe a homogeneous wire with a near round section and seams on the surface similar to those produced by strip-twisting. Further examination of the wires is in progress at the NMS in order to verify whether the same techniques were generally used throughout the 17th and 18th Dynasties.

4. Conclusion

21This study represents a first approach to the production techniques of Egyptian gold jewellery by presenting results obtained for a group of items from the collections of the NMS, dated to a period between the 19th and the 13th centuries BC. We have shown that the gold alloys used during this period are preponderantly produced with alluvial gold containing iridium-ruthenium-osmium inclusions. The alloys used to produce the studied jewellery range from high purity ones, with a gold content that can reach 95%, to electrum containing 51 to 53% silver. Apart from objects in which copper was certainly added to the alloy, the copper content was typically found to be below 2%.

Figure 6: Amarna finger-rings: (a) X-Radiograph of A.1883.49.8 showing the construction of the bezel and (b) detail of A.1883.49.2 showing the work of the wire coiled upon each end of bezel.
Figure 6 : Bagues d’Amarna : (a) radiographie X de A.1883.49.8 montrant le montage du chaton et (b) détail de A.1883.49.2 illustrant le travail du fil enroulé autour de l’anneau de chaque côté du chaton.

Figure 6: Amarna finger-rings: (a) X-Radiograph of A.1883.49.8 showing the construction of the bezel and (b) detail of A.1883.49.2 showing the work of the wire coiled upon each end of bezel.Figure 6 : Bagues d’Amarna : (a) radiographie X de A.1883.49.8 montrant le montage du chaton et (b) détail de A.1883.49.2 illustrant le travail du fil enroulé autour de l’anneau de chaque côté du chaton.

22The use of filigree and granulation in the decoration of the Amarna finger-rings revealed the use of hard soldering, and traces of this technique were found in joints for the majority of the objects studied. The seams in the limited sample set of wires have sections that may indicate the use of strip-twisting.

The authors would like to thank colleagues at NMS, in particular Henrietta Lidchi and Lesley-Ann Liddiard from the World Cultures Department, for giving us access to the objects and supporting the project; colleagues at C2RMF, especially the AGLAE team and Thierry Borel for his help and advice on X-Radiography of gold objects; Katherine Eremin at the Harvard Art Museum for comments on her previous work; Susan La Niece and Nigel Meeks at the British Museum for their comments while writing the article, and finally the Eu-ARTECH project for funding the PIXE analysis.

Top of page

Bibliography

Ahmed, A.H., 2007. Diversity of platinum-group minerals in podiform chromitites of the late Proterozoic ophiolite, Eastern Desert, Egypt. Ore Geology Reviews 32: 1-19.

Andrews, C., 1990. Ancient Egyptian Jewellery. London, The British Museum Press.

Carroll, D.L., 1972. Wire drawing in Antiquity. American Journal of Archaeology76(3): 321-323.

Dran, J.C., Salomon, J., Calligaro, T. and Walter, P., 2004. Ion beam analysis of art works: 14 years of use in the Louvre. Nuclear Instruments and Methods in PhysicsResearch B 219-220: 7-15.

Eremin, K., Goring, E., Manley, W.P. and Cartwright, C., 2000. A 17th dynasty Egyptian Queen in Edinburgh? KMT Modern Journal of Egyptology 11(3): 32-40.

Frantz, J.H. and Schorsch, D., 1990. Egyptian Red Gold. Archeomaterials 4: 133-152.

Guerra, M.F., 2008. An overview on the ancient goldsmith’s skill and the circulation of gold in the past; the role of x-ray based techniques. X-ray Spectrometry 37: 317-327.

Guerra, M.F. and Calligaro, T., 2003. Gold cultural heritage objects: a review of studies of provenance and manufacturing technologies. Measurement Science and Technology 14: 1527-1537.

James, T.G.H., 1972. Gold Technology in Ancient Egypt. Mastery of Metal working methods. Gold Bulletin 2(5): 35-42.

Lilyquist, C., 1993. Granulation and Glass: Chronological and Stylistic Investigations at Selected Sites, ca. 2500-1400 B.C.E. Bulletin of the American Schools of Oriental Research 290/291: 29-94.

Lilyquist, C., 2003. The tomb of the three foreign wives of Tuthmosis III. New York, The Metropolitan Museum of Art.

Lucas, A. and Harris, J.R., 1962.Ancient Egyptian Materials and Industries. London, Edward Arnold Publishers Ltd.

Manley, W.P., Eremin, K., Shortland, A. and Wilkinson, C., 2002. The facial reconstruction of an Ancient Egyptian Queen. Journal of Audiovisual Media in Medicine 25(4): 155-159.

Martin, G.T., 1974.The Royal Tomb at El-‘Amarna, I. The Objects. London: Egypt Exploration Society.

Maryon, H., 1949. Metal Working in the Ancient World. American Journal of Archaeology 53(2): 93-125.

Meeks, N.D. and Tite, M.S., 1980. The analysis of Platinum-group Element inclusions in Gold Antiquities. Journal of Archaeological Science 7: 267-275.

Molly, E.W., 1959. Platinum deposits of Ethiopia. Economic Geology 54(3): 467-477.

Oddy, A., 1977. The production of gold wire in Antiquity. Hand-making methods before the introduction of the draw-plate. Gold Bulletin 3(10): 79-87.

Ogden, J., 1976. The so-called “platinum” inclusions in Egyptian goldwork. Journal of Egyptian Archaeology 62: 138-144.

Ogden, J., 1982. Jewellery of the Ancient world. London, Trefoil Books.

Ogden, J., 1992.Interpreting the past: Ancient Jewellery. London, The British Museum Press.

Ogden, J., 2000. Metals, inP.T. Nicholson, I. Shaw (eds.), Ancient Egyptian Materials and Technology. Cambridge, Cambridge University Press, 148-175.

Petrie, W.M.F., 1909.Qurneh. London: BSAE Publishing.

Pliny the Elder, Natural History, XXXIII, J. Bostock translation, London, Taylor and Francis.

Pollard, W.B., 1908. Gold, in J.E. Quibell(ed.), Tomb of Yuaa and Thuiu. Le Caire, Imprimerie de l’Institut français d’archéologie orientale, 77-78.

Ramage, A. and Craddock, P., 2000. King Croesus’ Gold. Excavations at Sardis and the History of Gold Refining. London, British Museum Press.

Royal Museum Register of Specimens. Art and Ethnographical Department. Volume 11 (Eleven). 1908 – 1913 (1908.311 – 1913.401): 82

Scheel, B., 1989.Egyptian Metalworking and Tools. Shire: Shire Egyptology, Shire Publications Ltd.

Schorsch, D., 1995. The gold and silver necklaces of Wah: a technical study of an unusual metallurgical joining method, in C. Brown, F. Macalister, M. Wright (eds.), Conservation in Ancient Egyptian Collections. London, Archetype Publications, 127-135.

Schorsch, D., 2001. Precious-Metal Polychromy in Egypt in the Time of Tutankhamun. Journal of Egyptian Archaeology 87: 55-71.

Scott, D., 1990. Soldering with gold alloys in ancient South America. Archaeometry 32: 183-190.

Tate,J., Eremin,K., Troalen,L., Guerra,M.F., Goring,E. and Manley,W.P., 2009. The 17th Dynasty Gold Necklace from Qurneh, Egypt. ArcheoSciences 33.

Williams, C.R., 1924.Catalogue of Egyptian Antiquities, Gold and Silver Jewelry and Related Objects. New York, The New York Historical Society.

Top of page

Notes

1 The pendant is 41 mm long by 19 mm high. It was excavated in the burial of a ten years old girl in Cemetery A/Tomb 72. Fish-shaped pendants, known as ńkhā, were usually worn by children or young women.

2 See Martin (1974, nos. 275 and 280). Dimensions: A.1883.49.2, diameter of hoop 28 mm (internal 16 mm), bezel 12 mm by 13 mm. A.1883.49.8, diameter of hoop 22 mm, bezel 13 mm by 9 mm.

3 The fly-pendants might have formed part of an official’s usekh-collar, cf. an example in The Egyptian Museum, Cairo (CG 52677). The pendants are nearly identical and are 11 mm long by 7 mm high.

4 In some apparent instances of forgery, the gold composition is exactly 22 carat, corresponding to English gold coinage from the early 20th century (Lucas 1962; Lilyquist 2003).

5 Compositions from assay analysis by W.B. Pollard (1908).

6 These new analyses confirm the surface analysis undertaken by Eremin et al. (2000).

Top of page

List of illustrations

Title Figure 1: Qurneh girdle (A.1909.527.17): (a) OM image showing some deformation of barrel beads; (b) X-radiograph showing small barrel beads that have slipped inside a wallet bead.Figure 1 : Ceinture de Qurneh (A.1909.527.17) : (a) image sous loupe binoculaire illustrant la déformation des perles coniques ; (b) radiographie X illustrant les petites perles coniques à l’intérieur d’une perle en portefeuille.
URL http://journals.openedition.org/archeosciences/docannexe/image/2095/img-1.jpg
File image/jpeg, 396k
URL http://journals.openedition.org/archeosciences/docannexe/image/2095/img-2.png
File image/png, 98k
Title Table 1: Compositional results (in wt%) of gold-silver-copper alloy standards by PIXE, XRF and SEM-EDS.Tableau 1 : Compositions (en %) des alliages étalons en or-argent-cuivre par PIXE, FX et MEB-EDS.
URL http://journals.openedition.org/archeosciences/docannexe/image/2095/img-3.png
File image/png, 51k
Title Figure 2: PGE inclusions in pendant (A.1914.1081) from el-Harāgeh by OM; (b) Qurneh child’s necklace (A.1909.527.11) by SEI.Figure 2 : Inclusions de platinoïdes (a [Voir planche couleur]) du pendantif (A.1914.1081) d’el-Harāgeh sous loupe binoculaire ; (b) du collier d’enfant de Qurneh (A.1909.527.11) au MEB.
URL http://journals.openedition.org/archeosciences/docannexe/image/2095/img-4.jpg
File image/jpeg, 1.2M
URL http://journals.openedition.org/archeosciences/docannexe/image/2095/img-5.jpg
File image/jpeg, 1.0M
Title Figure 3: Ternary diagram (gold, silver, copper) showing the average alloy composition of the jewellery investigated (for some objects, multiple analyses of the different components were undertaken).Figure 3 : Diagramme ternaire (or, argent, cuivre) montrant la composition moyenne des alliages des pièces d’orfèvrerie analysées (pour certains objets l’analyse a été effectuée pour leurs différentes parties).
URL http://journals.openedition.org/archeosciences/docannexe/image/2095/img-6.png
File image/png, 292k
Title Figure 4: Detail of solder in Qurneh child’s earring (A.1909.527.43) by OM and (b) Qurneh adult’s earrings (A.1909.527.18) by SEI.Figure 4 : Détail de la soudure des boucles d’oreilles de Qurneh de l’enfant (A.1909.527.43) sous loupe binoculaire; (b) de l’adulte (A.1909.527.18) au MEB.
URL http://journals.openedition.org/archeosciences/docannexe/image/2095/img-7.jpg
File image/jpeg, 1.1M
URL http://journals.openedition.org/archeosciences/docannexe/image/2095/img-8.jpg
File image/jpeg, 156k
Title Figure 5: Detail of granulation observed on the bezel of the finger-ring A.1883.49.2 by SEI.Figure 5 : Détail de la granulation du chaton de la bague A.1883.49.2 au MEB.
URL http://journals.openedition.org/archeosciences/docannexe/image/2095/img-9.jpg
File image/jpeg, 860k
Title Figure 6: Amarna finger-rings: (a) X-Radiograph of A.1883.49.8 showing the construction of the bezel and (b) detail of A.1883.49.2 showing the work of the wire coiled upon each end of bezel.Figure 6 : Bagues d’Amarna : (a) radiographie X de A.1883.49.8 montrant le montage du chaton et (b) détail de A.1883.49.2 illustrant le travail du fil enroulé autour de l’anneau de chaque côté du chaton.
URL http://journals.openedition.org/archeosciences/docannexe/image/2095/img-10.png
File image/png, 727k
URL http://journals.openedition.org/archeosciences/docannexe/image/2095/img-11.jpg
File image/jpeg, 612k
Top of page

References

Bibliographical reference

Lore G. Troalen, Maria Filomena Guerra, Jim Tate and Bill Manley, “Technological study of gold jewellery pieces dating from the Middle Kingdom to the New Kingdom in Egypt”ArcheoSciences, 33 | 2009, 111-119.

Electronic reference

Lore G. Troalen, Maria Filomena Guerra, Jim Tate and Bill Manley, “Technological study of gold jewellery pieces dating from the Middle Kingdom to the New Kingdom in Egypt”ArcheoSciences [Online], 33 | 2009, Online since 10 December 2012, connection on 28 March 2024. URL: http://journals.openedition.org/archeosciences/2095; DOI: https://doi.org/10.4000/archeosciences.2095

Top of page

About the authors

Lore G. Troalen

National Museums Scotland, Department of Conservation & Analytical Research – 242 West Granton Road, Edinburgh EH5 1JA. (l.troalen@nms.ac.uk)

By this author

Maria Filomena Guerra

Laboratoires du Centre de Recherche et de Restauration des Musées de France, UMR171 CNRS – 14, quai François Mitterrand, 75001 Paris, France. (maria.guerra@culture.gouv.fr)

By this author

Jim Tate

National Museums Scotland, Department of Conservation & Analytical Research – 242 West Granton Road, Edinburgh EH5 1JA. (j.tate@nms.ac.uk)

By this author

Bill Manley

National Museums Scotland, Department of World Cultures, – Chambers Street, Edinburgh EH1 1JF. (b.manley@nms.ac.uk)

By this author

Top of page

Copyright

CC-BY-NC-ND-4.0

The text only may be used under licence CC BY-NC-ND 4.0. All other elements (illustrations, imported files) are “All rights reserved”, unless otherwise stated.

Top of page
Search OpenEdition Search

You will be redirected to OpenEdition Search